CBCBT - LATENT PRINT POWDER, SILVER/GRAY, BPP3028, BPP30216
- MSDS: CBCBT
- Manufacturer: SIRCHIE FINGER PRINT LABORATORIES INC
- Product Name: LATENT PRINT POWDER, SILVER/GRAY, BPP3028, BPP30216
- National Stock Number: 7510-00N038842
Product Identification
Product ID:LATENT PRINT POWDER, SILVER/GRAY, BPP3028, BPP30216
MSDS Date:06/01/1994
FSC:7510
NIIN:00N038842
MSDS Number: CBCBT
Responsible Party
RALEIGH, NC 27613
US
Emergency Phone: 919-781-3120
Info Phone: 919-781-3120
Cage: 94514
Contractor
Telephone: 919-554-2244
Cage: 94514
Ingredients
TITANIUM OXIDE; (TITANIUM DIOXIDE)
CAS: 13463-67-7
RTECS: XR2275000
Fraction By Weight: 45%
OSHA PEL 15 MG/M3 TDUST
ACGIH TLV: 10 MG/M3 TDUST
ALUMINUM (SARA 313)
CAS: 7429-90-5
RTECS: BD0330000
Fraction By Weight: 25-30%
OSHA PEL 15 MG/M3 DUST
ACGIH TLV: 10 MG/M3 DUST
LYCOPODIUM
CAS: 8023-70-9
Fraction By Weight: 30%
OSHA PEL N/K
ACGIH TLV: N/K
Hazards
LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:NO Skin:YES Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:PROLONGED EXPOSURE MAY CAUSE SLIGHT
SKIN IRRITATION AND MILD TO MODERATE EYE AND MUCOUS MEMBRANE
IRRITATION.
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.
First Aid
First Aid:INHALATION:REMOVE TO FRESH AIR. IF NOT BREATHING, GIVE IAR.
IF BREATHING IS DIFFICULT, GIVE OXYGEN. CALL A PHYSICIAN.
EYES:FLUSH IMMEDIATELY WITH PLENTY OF WATER FOR AT LEAST 15
MINUTES. CALL A PHYSIC IAN. SKIN:CMPD NOT LIKELY TO BE HAZ, BUT
CLEANSING AFTER USE IS ADVISEABLE. INGESTION:NO SPECIFIC
INTERVENTION IS INDICATED AS CMPD IS NOT LIKELY TO BE HAZ. IF SYMPS
OCCUR, CONSULT A PHYSICIAN.
Fire Fighting
Extinguishing Media:DRY CHEMICAL, SAND, GRAPHITE TO SMOTHER FLAME.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA & FULL
PROTECTIVE EQUIPMENT . NONE.
Unusual Fire/Explosion Hazard:ALL DUSTS AND POWDERS CAN POSE DUST
EXPLOSION HAZARD IF DISPERSED IN AIR. AVOID IGNITION SOURCES.
Accidental Release
Spill Release Procedures:DRY SWEEP SPILL INTO CONTAINER.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.
Handling
Handling and Storage Precautions:KEEP IN DRY CONTAINER. AVOID CREATING
DUST.
Other Precautions:NONE SPECIFIED BY MANUFACTURER.
Exposure Controls
Respiratory Protection:AVOID BREATHING DUST. USE NIOSH/MSHA APPROVED
DUST MASK.
Ventilation:SUFFICIENT TO KEEP AIR CONTAMINATION BELOW EXPOSURE LIMITS.
Protective Gloves:IMPERVIOUS GLOVES .
Eye Protection:ANSI APPROVED CHEM WORKERS GOGGS .
Other Protective Equipment:ANSI APPROVED EMERGENCY EYE WASH AND DELUGE
SHOWER .
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
NONE SPECIFIED BY MANUFACTURER.
Chemical Properties
Solubility in Water:PARTIALLY
Appearance and Odor:FINE SILVER/GRAY POWDER
Stability
Stability Indicator/Materials to Avoid:YES
ACIDS, STRONG ALKALIES, STRONG BASES, STRONG OXIDIZERS.
Stability Condition to Avoid:EXPOSURE TO WATER.
Hazardous Decomposition Products:MAY REACT WITH WATER TO FORM HYDROGEN
GAS.
Disposal
Waste Disposal Methods:DISPOSE OF IN ACCORDANCE WITH FEDERAL, STATE AND
LOCAL REGULATIONS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.